Alphatech5
 

Geothermal Energy Information

Google+

 

 

Search our Site - Google Custom Search

 


 


 

Google 

 

 

How Geothermal Energy Works

Introduction


Heat from the earth can be used as an energy source in many ways, from large and complex power stations to small and relatively simple pumping systems. This heat energy, known as geothermal energy, can be found almost anywhere—as far away as remote deep wells in Indonesia and as close as the dirt in our backyards.
Many regions of the world are already tapping geothermal energy as an affordable and sustainable solution to reducing dependence on fossil fuels, and the global warming and public health risks that result from their use. For example, more than 8,900 megawatts (MW) of large, utility-scale geothermal capacity in 24 countries now produce enough electricity to meet the annual needs of nearly 12 million typical U.S. households (GEA 2008a). Geothermal plants produce 25 percent or more of electricity in the Philippines, Iceland, and El Salvador.
The United States has more geothermal capacity than any other country, with more than 3,000 megawatts in eight states. Eighty percent of this capacity is in California, where more than 40 geothermal plants provide nearly 5 percent of the state’s electricity.
In thousands of homes and buildings across the United States, geothermal heat pumps also use the steady temperatures just underground to heat and cool buildings, cleanly and inexpensively.


geopower1

 

The Geothermal Resource

Below the Earth's crust, there is a layer of hot and molten rock called magma. Heat is continually produced there, mostly from the decay of naturally radioactive materials such as uranium and potassium. The amount of heat within 10,000 meters (about 33,000 feet) of Earth's surface contains 50,000 times more energy than all the oil and natural gas resources in the world.

 
The areas with the highest underground temperatures are in regions with active or geologically young volcanoes. These "hot spots" occur at plate boundaries or at places where the crust is thin enough to let the heat through. The Pacific Rim, often called the Ring of Fire for its many volcanoes, has many hot spots, including some in Alaska, California, and Oregon. Nevada has hundreds of hot spots, covering much of the northern part of the state.

These regions are also seismically active. Earthquakes and magma movement break up the rock covering, allowing water to circulate. As the water rises to the surface, natural hot springs and geysers occur, such as Old Faithful at Yellowstone National Park. The water in these systems can be more than 200°C (430°F).

Seismically active hotspots are not the only places where geothermal energy can be found.  There is a steady supply of milder heat—useful for direct heating purposes—at depths of anywhere from 10 to a few hundred feet below the surface virtually in any location on Earth.  Even the ground below your own backyard or local school has enough heat to control the climate in your home or other buildings in the community.  In addition, there is a vast amount of heat energy available from dry rock formations very deep below the surface (4–10 km). Using a set of emerging technologies known as Enhanced Geothermal Systems (EGS), we may be able to capture this heat for electricity production on a much larger scale than conventional technologies allow.



geopower2



If these resources can be tapped, they offer enormous potential for electricity production capacity. In its first comprehensive assessment in more than 30 years, the U.S. Geological Survey (USGS) estimated that conventional geothermal sources on private and accessible public lands across 13 western states have the potential capacity to produce 8,000–73,000 MW, with a mean estimate of 33,000 MW.  State and federal policies are likely to spur developers to tap some of this potential in the next few years. The Geothermal Energy Association estimates that 132 projects now under development around the country could provide up to 6,400 megawatts of new capacity.  As EGS technologies improve and become competitive, even more of the largely untapped geothermal resource could be developed. The USGS study found that hot dry rock resources could provide another 345,100–727,900 MW of capacity, with a mean estimate of 517,800 MW. That means that this resource could one day supply nearly all of today’s U.S. electricity needs. 

Not only do geothermal resources in the United States offer great potential, they can also provide continuous baseload electricity. According to the U.S. National Renewable Energy Laboratory, the capacity factors of geothermal plants—a measure of the ratio of the actual electricity generated over time compared to what would be produced if the plant was running nonstop for that period—are comparable with those of coal and nuclear power.  With the combination of both the size of the resource base and its consistency, geothermal can play an indispensable role in a cleaner, more sustainable power system.

 

How Geothermal Energy Is Captured

Geothermal springs for power plants. The most common current way of capturing the energy from geothermal sources is to tap into naturally occurring "hydrothermal convection" systems where cooler water seeps into Earth's crust, is heated up, and then rises to the surface. When heated water is forced to the surface, it is a relatively simple matter to capture that steam and use it to drive electric generators. Geothermal power plants drill their own holes into the rock to more effectively capture the steam.

There are three designs for geothermal power plants, all of which pull hot water and steam from the ground, use it, and then return it as warm water to prolong the life of the heat source. In the simplest design, the steam goes directly through the turbine, then into a condenser where the steam is condensed into water. In a second approach, very hot water is depressurized or "flashed" into steam which can then be used to drive the turbine.

In the third approach, called a binary system, the hot water is passed through a heat exchanger, where it heats a second liquid—such as isobutane—in a closed loop. The isobutane boils at a lower temperature than water, so it is more easily converted into steam to run the turbine. The three systems are shown in the diagrams below.

 

geopower3   geopower4  geopower5

 Dry steam

 Flash steam

 Binary cycle

The choice of which design to use is determined by the resource. If the water comes out of the well as steam, it can be used directly, as in the first design. If it is hot water of a high enough temperature, a flash system can be used, otherwise it must go through a heat exchanger. Since there are more hot water resources than pure steam or high-temperature water sources, there is more growth potential in the heat exchanger design.

The largest geothermal system now in operation is a steam-driven plant in an area called the Geysers, north of San Francisco, California. Despite the name, there are actually no geysers there, and the heat that is used for energy is all steam, not hot water. Although the area was known for its hot springs as far back as the mid-1800s, the first well for power production was drilled in 1924. Deeper wells were drilled in the 1950s, but real development didn't occur until the 1970s and 1980s. By 1990, 26 power plants had been built, for a capacity of more than 2,000 MW.


geopower6


The Geysers


Because of the rapid development of the area in the 1980s, and the technology used, the steam resource has been declining since 1988. Today, owned primarily by California- utility Calpine and with a net operating capacity of 725 MW, the Geysers facilities still meets nearly 60 percent of the average electrical demand for California's North Coast region (from the Golden Gate Bridge north to the Oregon border).  The plants at the Geysers use an evaporative water-cooling process to create a vacuum that pulls the steam through the turbine, producing power more efficiently. But this process loses 60 to 80 percent of the steam to the air, without re-injecting it underground. While the steam pressure may be declining, the rocks underground are still hot. To remedy the situation, various stakeholders partnered to create the Santa Rosa Geysers Recharge Project, which involves transporting 11 million gallons per day of treated wastewater from neighboring communities through a 40-mile pipeline and injecting it into the ground to provide more steam. The project came online in 2003, and in 2008 provided enough additional electricity for approximately 100,000 homes.  The city of Santa Rosa plans to further expand this program by increasing the amount of wastewater sent to the Geysers to nearly 20 million gallons per day. 

One concern with open systems like the Geysers is that they emit some air pollutants. Hydrogen sulfide—a toxic gas with a highly recognizable "rotten egg" odor—along with trace amounts of arsenic and minerals, is released in the steam. In addition, at a power plant at the Salton Sea reservoir in Southern California, a significant amount of salt builds up in the pipes and must be removed. While the plant initially started to put the salts into a landfill, they now re-inject the salt back into a different well. With closed-loop systems, such as the binary system, there are no emissions; everything brought to the surface is returned underground.

geopower7

 

Direct use of geothermal heat. Geothermal springs can also be used directly for heating purposes. Hot spring water is used to heat greenhouses, to dry out fish and de-ice roads, for improving oil recovery, and to heat fish farms and spas. In Klamath Falls, Oregon, and Boise, Idaho, geothermal water has been used to heat homes and buildings for more than a century. On the east coast, the town of Warm Springs, Virginia obtains heat directly from spring water as well, using springs to heat one of the local resorts.

In Iceland, virtually every building in the country is heated with hot spring water. In fact, Iceland gets more than 50 percent of its energy from geothermal sources.  In Reykjavik, for example (population 115,000), hot water is piped in from 25 kilometers away, and residents use it for heating and for hot tap water. 


Ground-source heat pumps. A much more conventional way to tap geothermal energy is by using geothermal heat pumps to provide heat and cooling to buildings. Also called ground-source heat pumps, they take advantage of the constant year-round temperature of about 50°F that is just a few feet below the ground’s surface. Either air or antifreeze liquid is pumped through pipes that are buried underground, and re-circulated into the building. In the summer, the liquid moves heat from the building into the ground. In the winter, it does the opposite, providing pre-warmed air and water to the heating system of the building.


geopower8

Ground Source Heat Pump

In the simplest use of ground-source heating and cooling, a tube runs from the outside air, under the ground, and into a house's ventilation system. More complicated, but more effective systems use compressors and pumps—as in electric air conditioning systems—to maximize the heat transfer.

In regions with temperature extremes, such as the northern United States in the winter and the southern United States in the summer, ground-source heat pumps are the most energy-efficient and environmentally clean heating and cooling system available.  Far more efficient than electric heating and cooling, these systems can move as much as 3 to 5 times the energy they use in the process. The U.S. Department of Energy found that heat pumps can save a typical home hundreds of dollars in energy costs each year, with the system typically paying for itself in 8 to 12 years. Tax credits and other incentives can reduce the payback period to 5 years or less.    

                                              
More than 600,000 ground-source heat pumps supply climate control in U.S. homes and other buildings, with new installations occurring at a rate of about 60,000 per year.   While this is significant, it is still only a small fraction of the U.S. heating and cooling market, and several barriers to greater penetration into the market remain. For example, despite their long-term savings, geothermal heat pumps have higher up-front costs. In addition, installing them in existing homes and businesses can be difficult, since it involves digging up areas around a building’s structure. Finally, many heating and cooling installers are just not familiar with the technology.

However, ground-source heat pumps are catching on in some areas. In rural areas without access to natural gas pipelines, homes must use propane or electricity for heating and cooling. Heat pumps are much less expensive to operate, and since buildings are widely spread out, installing underground loops is not an issue. Underground loops can be easily installed during construction of new buildings as well, resulting in savings for the life of the building.  Furthermore, recent policy developments are offering strong incentives for homeowners to install these systems.  The 2008 economic stimulus bill, Emergency Economic Stabilization Act of 2008, includes an eight year extension (through 2016) of the 30 percent investment tax credit, with no upper limit, to all home installations of EnergyStar certified geothermal heat pumps.

The Future of Geothermal Energy

Geothermal energy has the potential to play a significant role in moving the United States (and other regions of the world) toward a cleaner, more sustainable energy system. It is one of the few renewable energy technologies that—like fossil fuels—can supply continuous, baseload power. The costs for electricity from geothermal facilities are also declining. Some geothermal facilities have realized at least 50 percent reductions in the price of electricity since 1980. A considerable portion of potential geothermal resources will be able produce electricity for as little as 8 cents per kilowatt-hour (including a production tax credit), a cost level competitive with new conventional fossil fuel-fired power plants.  There is also a bright future for the direct use of geothermal resources as a heating source for homes and businesses in any location. However, in order to tap into the full potential of geothermal energy, two emerging technologies require further development: Enhanced Geothermal Systems (EGS) and co-production of geothermal electricity in oil and gas wells.  


Enhanced Geothermal Systems. Geothermal heat occurs everywhere under the surface of the earth, but the conditions that make water circulate to the surface are found only in less than 10 percent of Earth's land area. An approach to capturing the heat in dry areas is known as enhanced geothermal systems (EGS) or "hot dry rock". The hot rock reservoirs, typically at greater depths below the earth’s surface than conventional sources, are first broken up by pumping high-pressure water through them. The plants then pump more water through the broken hot rocks, where it heats up, returns to the surface as steam, and powers turbines to generate electricity. Finally, the water is returned to the reservoir through injection wells to complete the circulation loop. Plants that use a closed-loop binary cycle release no fluids or heat-trapping emissions other than water vapor, which may be used for cooling.


The Department of Energy, several universities, the geothermal industry, and venture capital firms (including Google) are collaborating on research and demonstration projects to harness the potential of hot dry rock. Australia, France, Germany, and Japan also have R&D programs to make EGS commercially viable. The DOE hopes to have EGS ready for commercial development by 2015 and is currently funding several demonstration projects.
geopower9

One cause for careful consideration with EGS is the possibility of induced seismic activity that might occur from hot dry rock drilling and development.  This risk is similar to that associated with hydraulic fracturing, an increasingly used method of oil and gas drilling, and with carbon dioxide capture and storage in deep saline aquifers. Though a potentially serious concern, the risk of an induced EGS-related seismic event that can be felt by the surrounding population or that might cause significant damage currently appears very low when projects are located an appropriate distance away from major fault lines and properly monitored. Appropriate site selection, assessment and monitoring of rock fracturing and seismic activity during and after construction, and open and transparent communication with local communities are also critical.


Co-production of Geothermal Electricity in Oil and Gas Wells. Oil and gas fields already under production represent another large potential source of geothermal energy.  In many existing oil and gas reservoirs, a significant amount of high-temperature water or suitable high-pressure conditions are present, which could allow for the production of electricity and oil or gas at the same time. In some cases, exploiting these resources could even enhance the extraction of the oil and gas itself.  An MIT study estimated that the United States has the potential to develop 44,000 MWs of geothermal capacity by 2050 by co-producing electricity, oil, and natural gas at oil and gas fields—primarily in the Southeast and southern Plains states. The study projects that such advanced geothermal systems could supply 10 percent of U.S. baseload electricity by that year, given R&D and deployment over the next 10 years.


These exciting new developments in geothermal will be supported by unprecedented levels of federal R&D funding. Under, the American Recovery and Investment Act of 2009, $400 million of new funding was allocated to the DOE’s Geothermal Technologies Program. Of this $90 million is expected to go towards a series of up to 10 demonstration projects to prove the feasibility of EGS technology. Another $50 million will fund up to 20 demonstration projects for other new technologies, including co-production with oil and gas and low temperature geothermal. The remaining funds will go exploration technologies, expanding the deployment of geothermal heat pumps, and other uses. These investments will very likely produce great net benefits in the future.

Geothermal Energy Basics NREL)

geopower10


The Earth's heat—called geothermal energy—escapes as steam at a hot springs in Nevada.

Other Resources

Geothermal Technologies Program
U.S. Department of Energy
Geothermal Heat Pumps
U.S. Department of Energy's Energy Savers


Many technologies have been developed to take advantage of geothermal energy—the heat from the earth. This heat can be drawn from several sources: hot water or steam reservoirs deep in the earth that are accessed by drilling; geothermal reservoirs located near the earth's surface, mostly located in the western U.S., Alaska, and Hawaii; and the shallow ground near the Earth's surface that maintains a relatively constant temperature of 50°-60°F.


This variety of geothermal resources allows them to be used on both large and small scales. A utility can use the hot water and steam from reservoirs to drive generators and produce electricity for its customers. Other applications apply the heat produced from geothermal directly to various uses in buildings, roads, agriculture, and industrial plants. Still others use the heat directly from the ground to provide heating and cooling in homes and other buildings.


NREL helps advance technologies for the following geothermal applications:

  • Direct use — Producing heat directly from hot water within the earth.
  • Electricity production — Generating electricity from the earth's heat.
  • Heat pumps — Using the Earth's shallow ground temperature for heating and cooling.

Learn more about NREL's geothermal capabilities and projects related to geothermal energy.

 

Geothermal Direct Use

 

geopower11


Geothermally heated waters allow alligators to thrive on a farm in Colorado, where temperatures can drop below freezing.


Geothermal reservoirs of hot water, which are found a few miles or more beneath the Earth's surface, can be used to provide heat directly. This is called the direct use of geothermal energy.
Geothermal direct use has a long history, going back to when people began using hot springs for bathing, cooking food, and loosening feathers and skin from game. Today, hot springs are still used as spas. But there are now more sophisticated ways of using this geothermal resource.


In modern direct-use systems, a well is drilled into a geothermal reservoir to provide a steady stream of hot water. The water is brought up through the well, and a mechanical system—piping, a heat exchanger, and controls—delivers the heat directly for its intended use. A disposal system then either injects the cooled water underground or disposes of it on the surface.


Geothermal hot water can be used for many applications that require heat. Its current uses include heating buildings (either individually or whole towns), raising plants in greenhouses, drying crops, heating water at fish farms, and several industrial processes, such as pasteurizing milk.

 

Geothermal Electricity Production

 

geopower12


This geothermal power plant generates electricity for the Imperial Valley in California.


Geothermal power plants use steam produced from reservoirs of hot water found a few miles or more below the Earth's surface to produce electricity. The steam rotates a turbine that activates a generator, which produces electricity.


There are three types of geothermal power plants: dry steam, flash steam, and binary cycle.

Dry Steam

Dry steam power plants draw from underground resources of steam. The steam is piped directly from underground wells to the power plant where it is directed into a turbine/generator unit. There are only two known underground resources of steam in the United States: The Geysers in northern California and Yellowstone National Park in Wyoming, where there's a well-known geyser called Old Faithful. Since Yellowstone is protected from development, the only dry steam plants in the country are at The Geysers.

Flash Steam

Flash steam power plants are the most common and use geothermal reservoirs of water with temperatures greater than 360°F (182°C). This very hot water flows up through wells in the ground under its own pressure. As it flows upward, the pressure decreases and some of the hot water boils into steam. The steam is then separated from the water and used to power a turbine/generator. Any leftover water and condensed steam are injected back into the reservoir, making this a sustainable resource.

Binary Steam

Binary cycle power plants operate on water at lower temperatures of about 225°–360°F (107°–182°C). Binary cycle plants use the heat from the hot water to boil a working fluid, usually an organic compound with a low boiling point. The working fluid is vaporized in a heat exchanger and used to turn a turbine. The water is then injected back into the ground to be reheated. The water and the working fluid are kept separated during the whole process, so there are little or no air emissions.


Currently, two types of geothermal resources can be used in binary cycle power plants to generate electricity: enhanced geothermal systems (EGS) and low-temperature or co-produced resources.

Enhanced Geothermal Systems

EGS provide geothermal power by tapping into the Earth's deep geothermal resources that are otherwise not economical due to lack of water, location, or rock type. The U.S. Geological Survey estimates that potentially 500,000 megawatts of EGS resource is available in the western U.S.—about half of the current installed electric power generating capacity in the United States.


geopower13

See an animation that shows how an Enhanced Geothermal System works at the U.S. Department of Energy's Geothermal Technologies Program (GTP) website.

Low-Temperature and Co-Produced Resources

Low-temperature and co-produced geothermal resources are typically found at temperatures of 300°F (150°C) or less. Some low-temperature resources can be harnessed to generate electricity using binary cycle technology. Co-produced hot water is a byproduct of oil and gas wells in the United States. This hot water is being examined for its potential to produce electricity, helping to lower greenhouse gas emissions and extend the life of oil and gas fields.

Geothermal Heat Pump Basics

geopower14


The West Philadelphia Enterprise Center uses a geothermal heat pump system for more than 31,000 square feet of space.


Geothermal heat pumps take advantage of the nearly constant temperature of the Earth to heat and cool buildings. The shallow ground, or the upper 10 feet of the Earth, maintains a temperature between 50° and 60°F (10°–16°C). This temperature is warmer than the air above it in the winter and cooler in the summer.


Geothermal heat pump systems consist of three parts: the ground heat exchanger, the heat pump unit, and the air delivery system (ductwork). The heat exchanger is a system of pipes called a loop, which is buried in the shallow ground near the building. A fluid (usually water or a mixture of water and antifreeze) circulates through the pipes to absorb or relinquish heat within the ground.


Heat pumps work much like refrigerators, which make a cool place (the inside of the refrigerator) cooler by transferring heat to a relatively warm place (the surrounding room), making it warmer. In the winter, the heat pump removes heat from the heat exchanger and pumps it into the indoor air delivery system, moving heat from the ground to the building's interior. In the summer, the process is reversed, and the heat pump moves heat from the indoor air into the heat exchanger, effectively moving the heat from indoors to the ground. The heat removed from the indoor air during the summer can also be used to heat water, providing a free source of hot water.


Geothermal heat pumps use much less energy than conventional heating systems, since they draw heat from the ground. They are also more efficient when cooling your home. Not only does this save energy and money, it reduces air pollution.


All areas of the United States have nearly constant shallow-ground temperatures, which are suitable for geothermal heat pumps.

 

Energy Basics  (US Dept of Energy)

 
geopower15
Several geothermal power plants at The Geysers.


Geothermal energy—geo (earth) + thermal (heat)—is heat energy from the earth.

What is a geothermal resource?

Geothermal resources are reservoirs of hot water that exist at varying temperatures and depths below the Earth's surface. Mile-or-more-deep wells can be drilled into underground reservoirs to tap steam and very hot water that can be brought to the surface for use in a variety of applications, including electricity generation, direct use, and heating and cooling. In the United States, most geothermal reservoirs are located in the western states.


Geothermal energy is a vast underutilized heat and power resource that is renewable, baseload, domestic and clean.

Benefits of Geothermal Energy

Renewable—Through proper reservoir management, the rate of energy extraction can be balanced with a reservoir's natural heat recharge rate.
Baseload—Geothermal power plants produce electricity consistently, running 24 hours per day / 7 days per week, regardless of weather conditions.
Domestic—U.S. geothermal resources can be harnessed for power production without importing fuel.
Small Footprint—Geothermal power plants are compact; using less land per GWh (404 mi2) than coal (3642 mi2) wind (1335 mi2) or solar PV with center station (3237 mi2).*
Clean—Modern closed-loop geothermal power plants emit no greenhouse gasses; life cycle GHG emissions (50 g CO2 eq/kWhe) are four times less than solar PV, and six to 20 times lower than natural gas. Geothermal power plants consume less water on average over the lifetime energy output than the most conventional generation technologies.**


Geothermal energy videos and animations:

 

geopower16

 



 

 

mercedes benz SL63 Electric vehicle
 

Sign up for PayPal and start accepting credit card payments instantly.